HOT TO CUT & FIX A SUP PADDLE
How To Cut and Fix a SUP Paddle Together
This is a how to guide for how to cut an SBS fixed length paddle fallow the guide step by step or watch the video to create your perfect paddle.
Supplies Needed:
* Hacksaw * Masking Tape * Sanding Block * Medium Grit Sandpaper * Tape Measure
* Fine Tip Permanent Marker * Dust Mask (Optional) * 5 Minute Epoxy * Stir Stick * Mixing Tray
1) To measure paddle length, stand the paddle Upright next to you with the tip of the blade touching the ground.
2) Using a fine tip permanent marker, mark a line on the shaft where you will make the cut.
WARNING: Make sure to compensate for the additional length with the handle installed.
3) Wrap a strip of masking tape around the shaft where you put your mark to prevent splintering while cutting.
4) Using the hacksaw, cut the shaft. Note: Paddle length is a personal preference. We recommend the total paddle length to be approximately 8” to 12” above head level, including the additional length with the handle installed.
* A longer length shaft is recommended for racing and flat water cruising.
* A shorter length shaft is recommended for wave riding.
5). Using the sanding block, sand the end of the shaft flat and smooth out the edge. Remove the masking tape
Handle & Blade Installation
1) Using the mixing tray and stir stick, mix the epoxy thoroughly. And insert heat shrinking loop over paddle shaft
2) Coat the inside of the handle with the epoxy. Repeat this stage with the blade
3) Insert the handle onto the shaft. Line up the flat side of the handle with the outward facing blade while the epoxy is still wet.
4). Line up the flat side of the handle with the outward facing blade while the epoxy is still wet.
5) Once the handle has dried, drip a bead of epoxy around handle connection to prevent leakage. Wipe off any excess resin
6) Slide heat shrinking loop over blade and shaft connection and apply heat until tight
After this, your paddle should be complete and ready to youse, have fun and see you in the water.
Related Posts
Kelly Slater – How to Carve 360 in Surfing …
Kelly Slater - How to Carve 360 in Surfing ... Kelly Slater - How to Carve 360 in Surfing ... Yes when Kelly speaks we listen carve game and Airs in surfing the 11-time world champ talks about these 2 as totally different styles of surfing and can affect your...
Best Warm Ups For Surfers
BEST WARM UPS FOR SURFERSBefore hitting the surf it’s essential to warm up! Warming up helps to prepare your body for the coming activity and the body’s systems to reach a steady state of energy production whilst also preparing the muscles for exercise and raising...
Top 10 BEST Foods for Surfers
Surf Nutrition : Top 10 BEST Foods for Surfers Every surfer knows the feeling sliding down the face of a wave just can’t be beaten. We all want to surf more for longer with more energy but there usually come a time where our energy level start to dip. Knowing...
Top 10 Reasons a Stand Up Paddleboard is better than a kayak
10 Reasons - Stand Up Paddleboard is better than a kayak 1) Perspective: On a kayak, you sit. On a stand-up board–you stand. From standing you can just see so much more. Wildlife in the water around you, waves coming in on the horizon—standing just gives you a...
How to do a Top & Bottom Turn in Surfing
How to do a Top & Bottom Turn in Surfing The bottom turns along with the top turn are probably the 2 most crucial and fundamental moves in surfing. They are used every time you catch a wave, and every time you perform a manoeuvre. Mastering the...
Improve Your Round house Cut back
Improve Your Roundhouse Cut back The roundhouse cut back is one of the most stylish and functional manoeuvres in a surfers arsenal. The roundhouse cutback is a move that is used by surfers of all skill levels. It allows great rail control whilst being functional by...
